DIY:ZMR250

Back to Category:DIY

Information

This is the build log for my ZMR H250 Cloneout Quadcopter. This is the first multirotor I have ever attempted to build and as such it will be documented and treated as a learning experience. All of the information contained here-in has been gathered and processed into the information you see here.

Websites

• RC Groups : ZMR 250 (Blackout Clone)
• RC Groups : PDB for ZMR 250 Mystery Carbon Fiber Frame
• RC Groups : FrSky Taranis "Howto" Thread
• RC Groups : FrSky Taranis with OpenTX 2.0 and Beyond
• RC Groups : Afroflight Naze32 Setup Guide for Dummies
• RC Groups : Get Your Technician's License. It's Easy. Here's Why And How.

Parts List

Build Log

• Pre-Build Checklist.
  <img src="http://kyau.net/img/ZMR250/prebuild-1.jpg" width="259" height="194" alt="">
• Pull the frame and PDB out of the box.
  <img src="http://kyau.net/img/ZMR250/prebuild-2.jpg" width="259" height="194" alt="">

Motors

• Pull out all the motors, there are long and short screws (separate them).
  <img src="http://kyau.net/img/ZMR250/motors-1.jpg" width="259" height="194" alt="">
• Put the propeller shafts on the motors with 4 short screws.
  <img src="http://kyau.net/img/ZMR250/motors-2.jpg" width="259" height="194" alt="">
• Assemble the motors to the carbon fiber arms, use 2 long screws and 1 short for each motor (be sure to also seal with loctite). To determine which gets the long vs. short screws, look inside the motor at where the motor leads are attached. If the hole you are putting the screw through is above the motor cables you have to use the short screws so you dont short out the cables.
  <img src="http://kyau.net/img/ZMR250/motors-3.jpg" width="259" height="194" alt="">

Battery

• Plugged in the soldering iron (medium tip) to get it hot to solder the battery connector to the PCB.
  <img src="http://kyau.net/img/ZMR250/battery-1.jpg" width="259" height="194" alt="">
• Took this time to start charging one of the batteries I bought for the quad.
  <img src="http://kyau.net/img/ZMR250/battery-2.jpg" width="259" height="194" alt="">
• Soldered the connector to the board.
  <img src="http://kyau.net/img/ZMR250/battery-3.jpg" width="259" height="194" alt="">

ESCs

• Strip the sticker and current heat shrink off of the ESCs.
  <img src="http://kyau.net/img/ZMR250/esc-1.jpg" width="259" height="194" alt="">
• Repeat this for all four ESCs.
  <img src="http://kyau.net/img/ZMR250/esc-2.jpg" width="259" height="194" alt="">
• Plug the soldering iron back in (fine point tip).
• Desolder all of the motor leads from all four ESCs.
  <img src="http://kyau.net/img/ZMR250/esc-3.jpg" width="259" height="194" alt="">
• Cut the motor's lead wires to length for placement of ESCs on arms. Then solder the ESCs to the motors, remember to connect two in a 1:1, 2:2 & 3:3 configuration and the two other motors in a 1:1, 2:3 & 3:2 configuration.
  <img src="http://kyau.net/img/ZMR250/esc-4a.jpg" width="259" height="194" alt=""><img src="http://kyau.net/img/ZMR250/esc-4b.jpg" width="259" height="194" alt="">

References

• Naze Wiki: Howto FrSky Telemetry
• Sky Scratch: Using FrSky Telemetry with Naze32 and Cleanflight using softserial