Hyper-V Server 2016: Installation

UNDER CONSTRUCTION: The document is currently being modified!

 Back to Category:Windows

Introduction

Microsoft Hyper-V Server 2016 is a stand-alone product that contains only the Windows hypervisor, a Windows Server driver model, and virtualization components. The Windows hypervisor technology in Microsoft Hyper-V Server 2016 is the same as what's in the Hyper-V role on Windows Server 2016. Hyper-V Server has a Windows Server Core experience and as such doesn't have a graphical user interface (GUI).

Testing was done on my Dell PowerEdge R610, the following image was used:

en_microsoft_hyper-v_server_2016_x64_dvd_9347277.iso

Installation

Insert the Hyper-V Server boot media into the machine and reboot (or power on) the machine, booting from the inserted media. Follow the instructions on the screen to install and reboot.

Hyper-V Server only requires ~32GB of hard drive space. Perform a "Custom" install, partitioning the C: drive accordingly, then assign the rest to D: for virtual machines.

Upon reboot you will be prompted to set an Administrator password, doing so will log into the machine finalizing the installation.

Use the command prompt provided to launch Windows PowerShell.

C:\> powershell

Networking

Before Hyper-V itself can be setup, a strong networking backbone needs to be setup.

Rename the computer.

PS C:\> Rename-Computer -NewName SKYE

List the current network adapters.

PS C:\> Get-NetAdapter -Physical

The Dell R610 comes with a built-in quad-port NIC, one will be assigned to management while the other three will be teamed together for VMs.

First create the NIC team.

PS C:\> New-NetLbfoTeam -Name "Hyper-V Team" -TeamMembers "Ethernet 2", "Ethernet 3", "Ethernet 4"

Verify it created the team correctly.

PS C:\> Get-NetLbfoTeam

If you need to specify a VLAN for the NIC team, use Set-NetLbfoTeamNic -Team "Hyper-V Team" -VlanID 123.

Rename the original adapters for consistency.

PS C:\> Rename-NetAdapter -Name "Ethernet" -NewName "Management"

PS C:\> Rename-NetAdapter -Name "Ethernet 2" -NewName "Ethernet Team 1"

PS C:\> Rename-NetAdapter -Name "Ethernet 3" -NewName "Ethernet Team 2"

PS C:\> Rename-NetAdapter -Name "Ethernet 4" -NewName "Ethernet Team 3"

Static IP

In order to setup a static IP address DHCP has to be disabled, the current IPs have to be removed, then new IPs can be assigned.

Remove DHCP from both adapters.

PS C:\> Set-NetIPInterface -InterfaceAlias "Management" -Dhcp Disabled

PS C:\> Set-NetIPInterface -InterfaceAlias "Hyper-V Team" -Dhcp Disabled

Remove the current IP addresses from both adapters (use A to choose Yes to All when removing).

PS C:\> Get-NetAdapter -InterfaceAlias "Management" | Remove-NetIPAddress

PS C:\> Get-NetAdapter -InterfaceAlias "Hyper-V Team" | Remove-NetIPAddress

Set the IP information for both adapters.

PS C:\> New-NetIPAddress -InterfaceAlias "Management" -IPAddress 10.0.42.10 -AddressFamily IPv4 -PrefixLength 24 -DefaultGateway 10.0.42.1

PS C:\> New-NetIPAddress -InterfaceAlias "Hyper-V Team" -IPAddress 10.0.42.11 -AddressFamily IPv4 -PrefixLength 24 -DefaultGateway 10.0.42.1

Also add DNS servers for both.

PS C:\> Set-DnsClientServerAddress -InterfaceAlias "Management" -ServerAddress 10.0.42.1

PS C:\> Set-DnsClientServerAddress -InterfaceAlias "Hyper-V Team" -ServerAddress 10.0.42.1

Remote Management

In order to use RSAT and Windows Admin Center remotely a few changes need to be made.

Enable WinRM.

PS C:\> Enable-PSRemoting -SkipNetworkProfileCheck -Force

Enable remote authentication acceptance.

PS C:\> Enable-WSManCredSSP -Role server

Enable firewall rules for remote management.

PS C:\> Set-NetFirewallRule -DisplayGroup 'Windows Management Instrumentation (WMI)' -Enabled true -PassThru

PS C:\> Set-NetFirewallRule -DisplayGroup 'Remote Event Log Management' -Enabled true -PassThru

Housekeeping

Remove Windows Defender.

PS C:\> Uninstall-WindowsFeature -Name Windows-Defender

Finally reboot the machine to commit the machine name and IP changes.

PS C:\> Restart-Computer

Dell OpenManage System Administrator

If you are running this on a Dell server, you might also want to install OMSA. At this point you should be able to access the administrative shares for windows.

Copy the OMSA installer onto the Hyper-V Server using the admin shares (eg. \\SKYE\d$).

Run the EXE from the command prompt or PowerShell to extract to C:\OpenManage.

Run the pre-requisite checker.

PS C:\> C:\OpenManage\windows\PreReqChecker\RunPreReqChecker.exe /s

Provided no errors are seen, install OMSA.

PS C:\> msiexec /i C:\OpenManage\windows\SystemsManagementx64\SysMgmtx64.msi

During the installation it might be beneficial to choose Custom and then add the Remote Manager.

Once installed a firewall rule will be needed to access OMSA from another computer.

PS C:\> New-NetFirewallRule -Name Dell_OMSA -DisplayName "Dell OMSA" -Description "Dell OMSA Web Management" -Protocol TCP -Enabled True -Profile Any -Action Allow -LocalPort 1311