DIY:ZMR250: Difference between revisions
From Wiki³
| Line 22: | Line 22: | ||
# Put the propeller shafts on the motors with 4 short screws.<br/>[http://kyau.net/img/ZMR250/motors-2.jpg <img src="http://kyau.net/img/ZMR250/motors-2.jpg" width="259" height="194" alt="">] | # Put the propeller shafts on the motors with 4 short screws.<br/>[http://kyau.net/img/ZMR250/motors-2.jpg <img src="http://kyau.net/img/ZMR250/motors-2.jpg" width="259" height="194" alt="">] | ||
# Assemble the motors to the carbon fiber arms, use 2 long screws and 1 short for each motor (be sure to also seal with loctite).<br/>[http://kyau.net/img/ZMR250/motors-3.jpg <img src="http://kyau.net/img/ZMR250/motors-3.jpg" width="259" height="194" alt="">] | # Assemble the motors to the carbon fiber arms, use 2 long screws and 1 short for each motor (be sure to also seal with loctite).<br/>[http://kyau.net/img/ZMR250/motors-3.jpg <img src="http://kyau.net/img/ZMR250/motors-3.jpg" width="259" height="194" alt="">] | ||
# Plugged in the soldering iron to get it hot to solder the battery connector to the PCB.<br/>[http://kyau.net/img/ZMR250/battery-1.jpg <img src="http://kyau.net/img/ZMR250/battery-1.jpg" width="259" height="194" alt="">] | # Plugged in the soldering iron (medium tip) to get it hot to solder the battery connector to the PCB.<br/>[http://kyau.net/img/ZMR250/battery-1.jpg <img src="http://kyau.net/img/ZMR250/battery-1.jpg" width="259" height="194" alt="">] | ||
# Took this time to start charging one of the batteries I bought for the quad.<br/>[http://kyau.net/img/ZMR250/battery-2.jpg <img src="http://kyau.net/img/ZMR250/battery-2.jpg" width="259" height="194" alt="">] | # Took this time to start charging one of the batteries I bought for the quad.<br/>[http://kyau.net/img/ZMR250/battery-2.jpg <img src="http://kyau.net/img/ZMR250/battery-2.jpg" width="259" height="194" alt="">] | ||
# Soldered the connector to the board.<br/>[http://kyau.net/img/ZMR250/battery-3.jpg <img src="http://kyau.net/img/ZMR250/battery-3.jpg" width="259" height="194" alt="">] | # Soldered the connector to the board.<br/>[http://kyau.net/img/ZMR250/battery-3.jpg <img src="http://kyau.net/img/ZMR250/battery-3.jpg" width="259" height="194" alt="">] | ||
# Strip the sticker and current heat shrink off of the ESCs.<br/>[http://kyau.net/img/ZMR250/esc-1.jpg <img src="http://kyau.net/img/ZMR250/esc-1.jpg" width="259" height="194" alt="">] | |||
# Repeat this for all four ESCs.<br/>[http://kyau.net/img/ZMR250/esc-2.jpg <img src="http://kyau.net/img/ZMR250/esc-2.jpg" width="259" height="194" alt="">] | |||
# Plug the soldering iron back in (fine point tip). | |||
== {{icon24|book-brown}} References == | == {{icon24|book-brown}} References == | ||
Revision as of 19:23, 3 February 2015
Back to Category:DIY
Information
InformationThis is the build log for my ZMR H250 Cloneout Quadcopter. This is the first multirotor I have ever attempted to build and as such it will be documented and treated as a learning experience. All of the information contained here-in has been gathered and processed into the information you see here.
Websites
Websites- RC Groups : ZMR 250 (Blackout Clone)
- RC Groups : PDB for ZMR 250 Mystery Carbon Fiber Frame
- RC Groups : FrSky Taranis "Howto" Thread
- RC Groups : FrSky Taranis with OpenTX 2.0 and Beyond
- RC Groups : Afroflight Naze32 Setup Guide for Dummies
- RC Groups : Get Your Technician's License. It's Easy. Here's Why And How.
Parts List
Parts List
Build Log
Build Log- Pre-Build Checklist.
<img src="http://kyau.net/img/ZMR250/prebuild-1.jpg" width="259" height="194" alt=""> - Pull the frame and PDB out of the box.
<img src="http://kyau.net/img/ZMR250/prebuild-2.jpg" width="259" height="194" alt=""> - Pull out all the motors, there are long and short screws (separate them).
<img src="http://kyau.net/img/ZMR250/motors-1.jpg" width="259" height="194" alt=""> - Put the propeller shafts on the motors with 4 short screws.
<img src="http://kyau.net/img/ZMR250/motors-2.jpg" width="259" height="194" alt=""> - Assemble the motors to the carbon fiber arms, use 2 long screws and 1 short for each motor (be sure to also seal with loctite).
<img src="http://kyau.net/img/ZMR250/motors-3.jpg" width="259" height="194" alt=""> - Plugged in the soldering iron (medium tip) to get it hot to solder the battery connector to the PCB.
<img src="http://kyau.net/img/ZMR250/battery-1.jpg" width="259" height="194" alt=""> - Took this time to start charging one of the batteries I bought for the quad.
<img src="http://kyau.net/img/ZMR250/battery-2.jpg" width="259" height="194" alt=""> - Soldered the connector to the board.
<img src="http://kyau.net/img/ZMR250/battery-3.jpg" width="259" height="194" alt=""> - Strip the sticker and current heat shrink off of the ESCs.
<img src="http://kyau.net/img/ZMR250/esc-1.jpg" width="259" height="194" alt=""> - Repeat this for all four ESCs.
<img src="http://kyau.net/img/ZMR250/esc-2.jpg" width="259" height="194" alt=""> - Plug the soldering iron back in (fine point tip).
References
References- Naze Wiki: Howto FrSky Telemetry
- Sky Scratch: Using FrSky Telemetry with Naze32 and Cleanflight using softserial
